ABB接触器.pdf

Contactors type AF1350 / AF1650 2ABB 1SFC101005C0201 Description The AF1350/AF1650 3-pole contactors are of the block type design. ● Main poles and auxiliary contact blocks – 3 main poles, – 1 N.O. and 1 N.C. auxiliary contacts 1 contact block fitted on the left hand side. – 2 N.O. and 2 N.C. auxiliary contacts 1 contact block fitted on each side A maximum of 4 auxiliary contact blocks can be fitted on each contactor. ● Electronic control The contactors are fitted with an electronic coil interface controlled by a specific integrated circuit developed by ABB. Advantages – Wide voltage range, 100...250 V a.c. and d.c. – Can manage large voltage variations – Reduced power consumption – Very distinct closing and opening – Noise free – Can withstand voltage interruptions or voltage dips in the control supply ≤ 20 ms ● Control s The AF1350/AF1650 contactors are as standard equipped with low voltage s for control, for example by a PLC ☞ see drawing below AF1350/AF1650 3-pole Contactors a.c./d.c. Operated - Wide voltage range Electronic Coil Interface AF1350/AF1650 specific design Contactor closed Contactor open Normal range Operational limits Control voltage Position Uc min.Uc max. E1688DG 0.85 Uc min.1.1 Uc max. 0.77 Uc min. 0.55 Uc min. Control s AF1350/AF1650 Control circuit with electronic coil interface. E1689DG ON OFF_N COMMON ON OFF 24V 0VA2A1 Supply voltage X5 1 2 3 Contactor 1 L13 L2 For General Use. Max 1650A, 600AV AC Ui1000V 5 L3 2 T14 T26 T3 ABB3 1SFC 101005C0201 AF1350/AF1650 3-pole Contactors a.c./d.c. Operated - Wide voltage range Electronic Coil Interface Applications AF1350 and 1650 are modern and compact 3-pole contactors designed for heavy duty industrial applications. They are designed for carrying and switching both inductive AC-3 and resitive AC-1 loads. High mechanical and electrical endurance make them suitable also for motor applications. Typical applications are as – Transfer switch or as main isolation contactor in generator sets – Main contactor for static power switching – Main or by-pass contactor in windmills – Main or by-pass contactor for frequency drives and softstarters – Y/D starters for example on board ships The coil is electronically controlled with features such as wide coil voltage range, low pull-in value and low power consumption to mention some of the features. It can also be operated with a low voltage signal directly from a PLC. These contactors are fully tested together with ABB breakers to meet type 2 co-ordination. For motor applications there is a three phase electronic overload relay called E1250 DU available. ● The most compact 1650A contactor ● Modern family design to match other ABB products ● Type 2 coordinated with breakers ● Electronic coil interface ● PLC operation possible ● cULus approved ● Low environmental impact thanks to Life Cycle Assessment 4ABB 1SFC101005C0201 AF1350/AF1650 3-pole Contactors Ordering details CAL 18-11 ZL1650 ZW1650 VM1650 1SFC101009F02011SFC101008F0201 AF1350 / AF1650 1SFC101026F02011SFC101033F0201 1SFC101007F0201 1SFC101006F0201 ZAF1650 ZP1650 1SFC101024F0201 1SFC101025F0201 E1250 DU Contactor Terminal screws and fixing screws included Rated operationalAuxiliaryTypeOrder codeWeight currentcontactskg AC-1AC-3fitted θ 40 C400 V AA1 piece 135086011AF1350-30-111SFL 65 7001 R701134.00 22AF1350-30-221SFL 65 7001 R702234.00 1650105011AF1650-30-111SFL 67 7001 R701135.00 22AF1650-30-221SFL 67 7001 R702235.00 Accessories Auxiliary contact blocks side mounting For contactorContactTypeOrder codePackingWeight typeblockspieceskg AF1350, AF165011CAL18-111SFN 01 0720 R101120.050 11CAL18-11B 11SFN 01 0720 R331120.050 1 CAL18-11B is a block for mounting outside a CAL18-11 block. Main contact sets For contactorTypeOrder codePackingWeight typesetkg AF1350ZL13501SFN 16 6503 R100012.500 AF1650ZL16501SFN 16 6703 R100013.500 Arc chutes/De-ionizing plates For contactorTypeOrder codePackingWeight typesetkg AF1350, AF1650ZW16501SFN 16 6510 R100014.000 Coils For contactorTypeOrder codePackingWeight typesetkg AF1350, AF1650ZAF16501SFN 15 6570 R702610.900 Printed circuit-board For contactorTypeOrder codePackingWeight typesetkg AF1350, AF1650ZP16501SFN 16 6521 R107010.300 Mechanical interlocking of two horizontal mounted contactors For contactorTypeOrder codePackingWeight typesetkg AF1350, AF1650VM1650H1SFN 03 6503 R100016 Electronic overload relay - class 10, 20, 30 selectable For contactorTypeOrder codePackingWeight typesetkg AF1350, AF1650E1250 DU21SFA 73 9001 R1000110 2 mounting kit with busbars for contactor mounting included ABB5 1SFC 101005C0201 AF1350/AF1650 3-pole Contactors Technical Data Magnet System Characteristics Contactor typeAF1350/AF1650 Rated control circuit voltage Ucmin...Uc max – at 50 HzV100 ... 250 – at 60 HzV100 ... 250 – d.c.V100 ... 250 Coil operating limitsθ 70 C according to IEC 60947-4-10.85 x Uc min...1.1 x Uc max Drop-out voltage in of Uc min. level55 Coil consumption Average pull-in value50 HzVA1900 60 HzVA1900 d.c.z.W1700 Average holding value 50 HzVA/W48/17 60 HzVA/W48/17 d.c. W16 Operating time A1-A2 between coil energization and N.O. contact closingms50 ... 80 N.C. contact openingms50 ... 80 between coil de-energization and N.O. contact openingms35 ... 55 N.C. contact closingms35 ... 55 with PLC between coil energization and N.O. contact closingms40 ... 65 N.C. contact openingms40 ... 65 between coil de-energization and N.O. contact openingms10 ... 30 N.C. contact closingms10 ... 30 Main Pole - Utilization Characteristics Contactor typeAF1350AF1650 Rated operational voltage Ue max. V1000 Rated frequency limitsHz25 ... 400 Conventional free-air thermal current Ith acc. to IEC 60947-4-1, open contactors θ ≤ 40 CA13501650 with conductor cross-sectional areamm22//100 x5 13//100 x51 Rated operational current Ie/AC-1 for air temperature close to contactor θ ≤ 40 CA13501650 Ue max. 1000 Vθ ≤ 55 CA11501450 θ ≤ 70 C A10001270 with conductor cross-sectional areamm22//100 x5 13//100 x5 1 Utilization category AC-3 for air temperature close to contactor 55 C Rated operational current Ie AC-3 220-230-240 VA8601050 3-phase motors380-400 VA8601050 415 VA8601050 440 VA8601050 Rated operational power AC-3 1500 r.p.m. 50 Hz 220-230-240 V kW257315 1800 r.p.m. 60 Hz 380-400 VkW475560 3-phase motors415 VkW500600 440 VkW560670 Rated making capacity AC-3 according to IEC 60947-4-110 x Ie AC - 3 Rated breaking capacity AC-3 according to IEC 60947-4-18 x Ie AC - 3 Short-circuit protectionProduct coordination with ABB circuit breaker. Please consult your nearest sales office for more ination. Rated short-time withstand current Icw at 40 C ambient temp., in free air, from a cold state1 sA10 00012 000 10 sA8 00010 000 30 sA6 0007 500 1 minA4 5005 500 15 minA1 6002 200 Maximum breaking capacity cos ϕ 0.35 at 440 VA1000012000 Heat dissipation per pole Ie /AC-1 W8080 Ie /AC-3 W5050 Max. electrical switching frequency – for AC-1cycles/h60 – for AC-3cycles/h60 – for AC-2, AC-4cycles/h60 Electrical durability50 000 Mechanical durability – millions of operating cycles500 000 – max. mechanical switching frequencycycles/h60 1 Dimensions of the bars General Technical Data Contactor typeAF1350/AF1650 Rated insulation voltage Ui according to IEC 60947-4-1V1000 according to UL/CSAV600 Rated impulse withstand voltage Uimp.kV8 Standards Devices complying with - International standardsIEC 60947-1 / 60947-4-1 - European standardsEN 60947-1 / 60947-4-1 - UL508 Certifications - Approvals Air temperature close to contactor – fitted with electronic O/L relayC-25 to 70 – without electronic O/L relayC-40 to 70 – for storageC-40 to 70 Operating altitudem 3000 6ABB 1SFC101005C0201 AF1350/AF1650 3-pole Contactors Technical Data UL Amp-rating for AF1350/AF1650 The ”amp-rating” value corresponds to the ”General Use Rating” defined in specification UL508 the operational current, bot during pull-in and steady-state conditions, must not exceed the ”amp-rating” value of the device. In alternating current, the inductive cos ϕ of the load between 0.75 and 0.8. ContactorsMain contactsAuxiliary contacts General Use Rating NominalNominal”pilot duty”NominalNominal currentvoltagecurrentvoltage TypeAV a.c.AV a.c. AF13501350600A600, Q30010600 AF16501650600A600, Q30010600 3-phase motor-rating UL Approvals stipulate the following for contactors - the ”3-phase motor-rating” motor power hp and corresponding current A. - the ”amp-rating” usual operational current A and nominal voltage V. The technical characteristics figuring on devices must be respected and have been reproduced in the table below. ContactorsSizeMotor power P hp and nominal current Ie A NEMAUeUeUe 220V/240V440V/480V550V/600V TypehpAhpAhpA AF1350–4009548009541000954 AF165084501030900103011501050 ABB7 1SFC 101005C0201 Tripping curves for E1250 DU electronic overload relays Not suitable for single-phase and direct current d.c. motors Electronic overload relays E1250 DU for contactors AF1350/AF1650 Technical data Description The electronic overload realy type E1250 DU is available in the current range 375...1250 A. The E1250 DU is a 3-phase relay intended for a.c. circuits and is not suitable for single-phase or direct current d.c. circuits. The reset of the relay can be done manually or automatically. Tripping class can be set manually class 10, 20 or 30. A busbar kit for mounting the E1250 DU to the AF1350/AF1650 contactor is included. 1102357 1 10 100 10 1 Tripping characteristics 3-phase for electronic overload relay E1250 DU E1250 DU mean value [s] Class 30 138.4 71.7 44.4 30.2 20.8 16.7 92.6 47.9 29.5 20.2 13.9 11.1 46.2 23.9 14.8 10.1 6.9 5.6 3 4 5 6 7.2 8 Class 20Class 10I/Ie cold Class 30 Class 20 Class 10 warm SecondsMinutes Tripping time Operating current as a multiple of the setting current Technical data of the conducting paths Number of conducting paths3 Setting rangeA375 ... 1250 Tripping classes to IEC 60947-4-1/EN 60947-4-110, 20, 30 adjustable Frequency rangeHz50 and 60 only for a.c. operating 3 phase Load rating of auxiliary contacts ContactNC 95-96NO 97-98 Rated operating voltage UeV600600 Rated thermal continuous currentA66 Rated operating current Ie at AC-15230 VA33 at AC-15400 VA1.11.1 at AC-15500 VA0.90.9 at AC-15690 VA0.70.7 at DC-1324 VA1.51.5 at DC-1360 VA0.50.5 at DC-13110 VA0.40.4 at DC-13220 VA0.20.2 Short-circuit protection fuse gGA66 General technical data TypeE1250 DU StandardsIEC 60947-4-1 / IEC 60947-5-1 major European and international standardsEN 60947-4-1 / EN 60947-5-1 Approvals and certificates Rated insulation voltage UiV690 Rated operating voltage UeV690 Impulse withstand voltage UimpkV6 Permissible ambient temperature - Storage C- 25 to 70 - Operation C- 25 to 70 Mounting positionSame as Contactor AF1350/AF1650 Mountingby screws 4 x M6 Connection terminals and attachment type Auxiliary contacts Screw terminal screw size - with self-disengaging clamping pieceM3.5 Tightening torqueNm1 Connection cross-sections - single-core or strandedmm22 x 0.75...4 - flexible with wire end ferrulemm22 x 0.75...4 Connection terminals Main conductors Screw terminal screw sizeM12 Protection degree acc to IEC 60947-1/EN 60947-1IP00 8ABB 1SFC101005C0201 AF1350/AF1650 3-pole Contactors Dimensions and Drilling plans AF1350/AF1650 Contactor E1250 DU Electronic O/L relay AF1350/AF1650 Contactor DimensionsDrilling plan DimensionsDrilling plan ABB9 1SFC 101005C0201 AF1350/AF1650 3-pole Contactors Dimensions and Drilling plan PLC wiring and mounting positions When used with switches the wiring can be done as below. Control with logic control signals When used with transistor outputs the wiring can be done as below. Note Emergency stop should disconnect A1 and A2 879 441 256 5910 Dimensions Drilling plan For M8 12x 312 305136136136136 AF1350/AF1650 contactor VM1650H mechanical interlock A1A2 ON Stop 0V 24V Start OFF_N COM Supply voltage Contactor 3 2 1 X5 A1A2 ON OFF_N COM0V 24V Stop_n Start Supply voltage Contactor 3 2 1 X5 1SFC101021F0201 1SFC101022F0201 1SFC101018F0201 Note Emergency stop should disconnect A1 and A2 Mounting positions Pos.4 Pos.2 Pos.1 Pos.3 Pos.5 1L11L13L23L25L35L3 AF 1650-30 2T12T14T24T26T36T3 1SFC101034F0201 10ABB 1SFC101005C0201 Thermal/Electronic overload relay Auxiliary contact block Timer Interlock Front Mounting 1 x NO CA 5-101 x NC CA 5-01 Up to A/AF110 Side Mounting 1 NO 1 NC CAL 5-11CAL18-11 TA 42 DU 22...32 29...42 29...42 36...52 45...63 60...80 0.4 ...0.63 2.2...3.1 7.5...11 0.63...1.02.8...4.0 10 ...14 0.10...0.161.0 ...1.43.5...5.0 13 ...19 0.16...0.251.3 ...1.84.5...6.5 18 ...25 0.25...0.41.7 ...2.46.0...8.5 24 ...32 TA 25 DU Pneumatic 0.1 ... 40 s TP 40 10 ... 180 s TP 180 Types4-PoleA 9A 16A 26A 45A 50A 75 Rated current AC-1, 40 CIEC25 A30 A45 A70 A100 A125 A General use ratingUL21 A30 A40 A80 A80 A105 A Electronic TE5S T A 80 DU T A 110 DU 60...8065...90 80...110 TA 75 DU Types3-PoleA9A12A16A26 A30 A40A/AF50A/AF63 A/AF75A/AF95 A/AF110 Power rating AC-3, 220-240 V2.2 kW3 kW4 kW6.5 kW9 kW11 kW15 kW18.5 kW22 kW25 kW30 kW 380-400 VIEC4 kW 5.5 kW 7.5 kW11 kW15 kW 18.5 kW22 kW30 kW37 kW45 kW55 kW 690 V5.5 kW 7.5 kW9 kW15 kW 18.5 kW22 kW30 kW37 kW40 kW55 kW75 kW Rated current AC-1, 40 C25 A27 A30 A45 A55 A60 A100 A115 A125 A145 A160 A Power 220-240 V2 hp3 hp5 hp10 hp10 hp15 hp20 hp25hp30 hp30 hp40 hp 440-480 VUL5 hp7.5 hp10 hp20 hp25 hp30 hp40 hp60 hp60 hp60 hp75 hp 600 V 7.5 hp10 hp15 hp25 hp30 hp40 hp50 hp75 hp75 hp75 hp100 hp General use rating 21 A25 A30A40 A50 A60 A80 A90 A105 A125 A140 A Mechanical and electrical VE 5-1 Mechanical and electrical VE 5-2 A Comprehensive product portofolio A.., AF.., 3-pole Contactors A.., EK.., 4-pole Contactors ABB11 1SFC 101005C0201 Side Mounting 1 NO 1 NC CAL18-11 130 ... 175 150 ... 200 TA 200 DU E 200 DU 165 ... 235 220 ... 310 TA 450 DU E 320 DUE 500 DUE 800 DU 60 ... 200 100 ... 320 150 ... 500 250 ... 800 Electronic TE5S E 1250 DU375 ... 1250 4-PoleEK 110EK 150EK 175EK 210EK 370EK 550EK 1000 200 A250 A300 A350 A550 A800 A1000 A 170 A200 A250 A300 A420 A540 A– 3-PoleA/AF145 A/AF185A/AF210A/AF260 A/AF300AF400AF460AF580AF750AF1350AF1650 45 kW55 kW59 kW80 kW90 kW110 kW132 kW160 kW220 kW257 kW315 kW 75 kW90 kW110 kW140 kW160 kW200 kW250 kW315 kW400 kW475 kW560 kW 110 kW132 kW160 kW200 kW250 kW315 kW355 kW500 kW600 kW–– 250 A275 A350 A400 A500 A600 A700 A800 A1050 A 1350 A 1650 A 50 hp60 hp75 hp100 hp100 hp150 hp200 hp250 hp300 hp400 hp450 hp 100 hp125 hp150 hp200 hp250 hp350 hp400 hp500 hp600 hp800 hp900 hp 125 hp150 hp200 hp250 hp300 hp400 hp500 hp600 hp700 hp1000 hp1150 hp 230 A250 A300 A350 A400 A550 A650 A750 A900 A1350 A1650 A Mechanical VM 300H MechanicalMechanical VM 750HVM 1650H World-wide support, industry-wide experience Automation Technologies The Automatio