BS_EN_1090-1-2009_钢结构和铝结构的施工．结构零件一致性评估的要求.pdf

BS EN 1090-12009 ICS 91.080.10 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BRITISH STANDARD cution of steel structures and aluminium structures Part 1 Requirements for conity assessment of structural components This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 August 2009 BSI 2009 ISBN 978 0 580 54786 7 Amendments/corrigenda issued since publication DateComments BS EN 1090-12009 National foreword This British Standard is the UK implementation of EN 1090-12009. The UK participation in its preparation was entrusted to Technical Committee B/521, cution of steel structures. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. BS EN 1090-12009 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1090-1 July 2009 ICS 91.080.10 English Version cution of steel structures and aluminium structures - Part 1 Requirements for conity assessment of structural components Excution des structures en acier et des structures en aluminium - Partie 1 Exigences pour lvaluation de la conit des composants structuraux Ausfhrung von Stahltragwerken und Aluminiumtragwerken - Teil 1 Konittsnachweisverfahren fr tragende Bauteile This European Standard was approved by CEN on 15 June 2008. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions English, French, German. A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre Avenue Marnix 17, B-1000 Brussels 2009 CENAll rights of exploitation in any and by any means reserved worldwide for CEN national Members. Ref. No. EN 1090-12009 E BS EN 1090-12009 EN 1090-12009 E 2 Contents Page Foreword ..............................................................................................................................................................4 Introduction .........................................................................................................................................................5 1Scope ......................................................................................................................................................6 2Normative references ............................................................................................................................6 3Terms, definitions and abbreviations ..................................................................................................7 3.1Terms and definitions ...........................................................................................................................7 3.2Abbreviations .........................................................................................................................................8 4Requirements .........................................................................................................................................9 4.1Constituent products ............................................................................................................................9 4.1.1General ....................................................................................................................................................9 4.1.2Constituent products for steel components .......................................................................................9 4.1.3Constituent products for aluminium components .............................................................................9 4.2Tolerances on dimensions and shape ................................................................................................9 4.3Weldability ..............................................................................................................................................9 4.4Fracture toughness ............................................................................................................................ 10 4.5Structural characteristics .................................................................................................................. 10 4.5.1General ................................................................................................................................................. 10 4.5.2Load bearing capacity ........................................................................................................................ 10 4.5.3Fatigue strength .................................................................................................................................. 10 4.5.4Resistance to fire ................................................................................................................................ 10 4.6Reaction to fire .................................................................................................................................... 11 4.7Dangerous substances ...................................................................................................................... 11 4.8Impact resistance................................................................................................................................ 11 4.9Durability ............................................................................................................................................. 11 5uation s ............................................................................................................................ 12 5.1General ................................................................................................................................................. 12 5.2Constituent products ......................................................................................................................... 12 5.3Tolerances on dimensions and shape ............................................................................................. 12 5.4Weldability ........................................................................................................................................... 12 5.5Fracture toughness ............................................................................................................................ 12 5.6Structural characteristics .................................................................................................................. 12 5.6.1General ................................................................................................................................................. 12 5.6.2Structural design ................................................................................................................................ 13 5.6.3Manufacturing characteristics ........................................................................................................... 13 5.7Resistance to fire ................................................................................................................................ 13 5.8Reaction to fire .................................................................................................................................... 14 5.9Dangerous substances ...................................................................................................................... 14 5.10Impact resistance................................................................................................................................ 14 5.11Durability ............................................................................................................................................. 14 6uation of conity .................................................................................................................... 14 6.1General ................................................................................................................................................. 14 6.2Initial type testing ............................................................................................................................... 15 6.2.1General ................................................................................................................................................. 15 6.2.2Characteristics .................................................................................................................................... 15 6.2.3Use of historical data ......................................................................................................................... 16 6.2.4Use of structural calculations for conity assessment ............................................................ 16 6.2.5Initial type calculation ........................................................................................................................ 16 6.2.6Sampling, uation and conity criteria .................................................................................. 16 6.2.7Declaration of perance characteristics .................................................................................... 16 6.2.8Recording of results from uations ............................................................................................. 16 BS EN 1090-12009 EN 1090-12009 E 3 6.2.9Corrective actions ............................................................................................................................... 16 6.3Factory production control................................................................................................................. 18 6.3.1General ................................................................................................................................................. 18 6.3.2Personnel ............................................................................................................................................. 18 6.3.3Equipment ............................................................................................................................................ 18 6.3.4Structural design process .................................................................................................................. 18 6.3.5Constituent products used in manufacture ...................................................................................... 18 6.3.6Component specification.................................................................................................................... 19 6.3.7Product uation .............................................................................................................................. 19 6.3.8Non-coning products .................................................................................................................. 19 7Classification and designation .......................................................................................................... 20 8Marking ................................................................................................................................................. 21 Annex A inative Guidelines for preparation of the component specification .................................. 22 A.1General ................................................................................................................................................. 22 A.2Purchaser provided component specification PPCS .................................................................... 22 A.3Manufacturer provided component specification MPCS .............................................................. 22 Annex B normative Assessment of factory production control ................................................................ 24 B.1General ................................................................................................................................................. 24 B.2Initial inspection .................................................................................................................................. 24 B.3Continuous surveillance ..................................................................................................................... 25 B.4Frequency of inspection ..................................................................................................................... 26 B.4.1General ................................................................................................................................................. 26 B.4.2Surveillance intervals .......................................................................................................................... 26 B.4.3Declaration by manufacturer .............................................................................................................. 27 B.4.4Action in case of non-compliance ..................................................................................................... 27 B.5Reports ................................................................................................................................................. 27 Annex ZA inative Clauses of this European Standard Addressing the provisions of EU Construction Products Directive CPD ............................................................................................ 28 ZA.1Scope and relevant characteristics ................................................................................................... 28 ZA.2Procedures for the attestation of conity of structural steel and aluminium components ..................