BS_EN_1504-2-2004_混凝土结构保护和维修用产品和系统．定义、要求、质量控制和合格评估．混凝土表面防护系统.pdf

BRITISH STANDARD BS EN 1504-22004 Products and systems for the protection and repair of concrete structures Definitions, requirements, quality control and uation of conity Part 2 Surface protection systems for concrete The European Standard EN 1504-22004 has the status of a British Standard ICS 01.040.91; 91.080.40 BS EN 1504-22004 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 15 December 2004 BSI 15 December 2004 ISBN 0 580 45057 0 National foreword This British Standard is the official English language version of EN 1504-22004. EN 1504-2 is a candidate “harmonized” European standard and fully takes into account the requirements of the European Commission mandate M/128, Products related to concrete, mortar and grout, given under the EU Construction Products Directive 89/106/EEC, and is intended to lead to CE marking. The date of applicability of EN 1504-2 as a harmonized European Standard, i.e. the date after which this standard may be used for CE marking purposes, is subject to an announcement in the Official Journal of the European Communities. The Commission in consultation with Member States has agreed a transition period for the co-existence of harmonized European Standards and their corresponding national standards. It is intended that this period will comprise a period, usually nine months, after the date of availability of the European Standard, during which any required changes to national regulations are to be made, followed by a further period, usually of 12 months, for the implementation of CE marking. At the end of this co-existence period, the national standards will be withdrawn. EN 1504-2 is the subject of transitional arrangements agreed under the Commission mandate. In the UK, there are no corresponding national standards of national origin. The UK participation in its preparation was entrusted by Technical Committee B/517, Concrete, to Subcommittee B/517/8, Protection and repair of concrete structures, which has the responsibility to A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests ined; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 46, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. DateComments 标准分享网 w w w .b z f x w .c o m 免费下载 w w w . b z f x w . c o m EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1504-2 October 2004 ICS 01.040.91; 91.080.40 English version Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and uation of conity - Part 2 Surface protection systems for concrete Produits et systmes pour la protection et la rparation de structures en bton - Dfinitions, prescriptions, matrise de la qualit et valuation de la conit - Partie 2 Systmes de protection de surface pour bton Produkte und Systeme fr den Schutz und die Instandsetzung von Betontragwerken - Definitionen, Anforderungen, Qualittsberwachung und Beurteilung der Konitt - Teil 2 Oberflchenschutzsysteme fr Beton This European Standard was approved by CEN on 30 July 2004. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions English, French, German. A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre rue de Stassart, 36 B-1050 Brussels 2004 CENAll rights of exploitation in any and by any means reserved worldwide for CEN national Members. Ref. No. EN 1504-22004 E w w w . b z f x w . c o m EN 1504-22004 E 2 Contents page Foreword..............................................................................................................................................................3 Introduction.........................................................................................................................................................5 1 Scope ......................................................................................................................................................6 2 Normative references............................................................................................................................6 3 Terms and definitions ...........................................................................................................................9 4 Perance characteristics for intended uses...............................................................................10 4.1 General..................................................................................................................................................10 4.2 Selection of appropriate products or systems.................................................................................11 5 Requirements.......................................................................................................................................14 5.1 Identification requirements.................................................................................................................14 5.2 Perance requirements.................................................................................................................15 5.3 Release of dangerous substances.....................................................................................................15 5.4 Reaction to fire.....................................................................................................................................15 6 Sampling...............................................................................................................................................15 7 uation of conity.....................................................................................................................15 7.1 General..................................................................................................................................................15 7.2 Initial type testing ................................................................................................................................15 7.3 Factory production control.................................................................................................................15 7.4 Assessment, surveillance and certification of factory production control...................................16 8 Marking and labelling..........................................................................................................................16 Annex A inative Minimum frequency of testing for factory production control............................26 Annex B inative Examples of the application of the classification system in three individual cases...................................................................................................................................28 Annex C inative Release of dangerous substances.........................................................................29 Annex ZA inative Clauses addressing the provisions of EU Construction Products Directive................................................................................................................................................30 ZA.1 Scope and relevant characteristics ...................................................................................................30 ZA.2 Attestation of conity....................................................................................................................38 ZA.2.1 Systems of attestation of conity..............................................................................................38 ZA 2.2 EC Certificate and Declaration of conity...................................................................................41 ZA.3 CE marking and labelling....................................................................................................................43 Bibliography......................................................................................................................................................46 标准分享网 w w w .b z f x w .c o m 免费下载 w w w . b z f x w . c o m EN 1504-22004 E 3 Foreword This document EN 1504-22004 has been prepared by Technical Committee CEN/TC 104 “Concrete and related products”, the secretariat of which is held by DIN. It has been developed by sub-committee 8 “Products and systems for the protection and repair of concrete structures“, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2005, and conflicting national standards shall be withdrawn at the latest by December 2008. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive 89/106/EC. For relationship with EU Directives, see inative Annex ZA, which is an integral part of this document. This Part of EN 1504 does not supersede any other European Standard. This European Standard is one of a series of standards on products and systems for the repair and protection of concrete structures as listed below EN 1504-1, Products and systems for the protection and repair of concrete structures Definitions, requirements, quality control and uation of conity Part 1 Definitions. prEN 1504-31, Products and systems for the protection and repair of concrete structures Definitions , requirements, quality control and uation of conity Part 3 Structural and non-structural repair. EN 1504-4, Products and systems for the protection and repair of concrete structures Definitions, requirements, quality control and uation of conity Part 4 Structural bonding. EN 1504-5, Products and systems for the protection and repair of concrete structures Definitions, requirements, quality control and uation of conity Part 5 Concrete injection. prEN 1504-61, Products and systems for the protection and repair of concrete structures Definitions, requirements, quality control and uation of conity Part 6 Anchoring of reinforcing steel bar. prEN 1504-71, Products and systems for the protection and repair of concrete structures Definitions Requirements Quality control and uation of conity Part 7 Reinforcement corrosion protection. EN 1504-8, Products and systems for the protection and repair of concrete structures Definitions, requirements, quality control and uation of conity Part 8 Quality control and uation of conity. ENV 1504-92, Products and systems for the protection and repair of concrete structures Definitions, requirements, quality control and uation of conity Part 9 General principles for the use of products and systems. 1 To be published. 2 ENV 1504-9 will have to be modified when adopted as EN according to finalisation of this standard. w w w . b z f x w . c o m EN 1504-22004 E 4 EN 1504-10, Products and systems for the protection and repair of concrete structures Definitions Requirements Quality control and uation of conity Part 10 Site application of products and systems and quality control of the works. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. 标准分享网 w w w .b z f x w .c o m 免费下载 w w w . b z f x w . c o m EN 1504-22004 E 5 Introduction This document gives specifications for products and systems for the repair and protection of concrete structures. The test s to which the specifications refer are the subject of separate standards. Surface protection systems are used as “s” for the following “principles“ presented in ENV 1504-9 for Principle 1 PI Protection against Ingress 1.1 hydrophobic impregnation H 1.2 impregnation I 1.3 coating C for Principle 2 MC Moisture Control 2.1 hydrophobic impregnation H 2.2 coating C for Principle 5 PR Physical Resistance/Surface Improvement 5.1 coating C 5.2 impregnation I for Principle 6 RC Resistance to Chemicals 6.1 coating C for Principle 8 IR Increasing Resistivity by Limiting moisture content 8.1 hydrophobic impregnation H 8.2 coating C w w w . b z f x w . c o m EN 1504-22004 E 6 1 Scope This document specifies requirements for the identification, perance including durability aspects,