BS DD CENTS 1852-2-2009 地下无压力排水和排污用塑料管道系统.聚丙烯(PP).一致性评估指南.pdf

DD CEN/TS 1852-22009 ICS 23.040.01; 93.030 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW DRAFT FOR DEVELOPMENT Plastics piping systems for non-pressure underground drainage and sewerage Polypropylene PP Part 2 Guidance for the assessment of conity This Draft for Development was published under the authority of the Standards Policy and Strategy Committee on 30 June 2009. BSI 2009 ISBN 978 0 580 59022 1 Amendments/corrigenda issued since publication DateComments DD CEN/TS 1852-22009 National foreword This Draft for Development is the UK implementation of CEN/TS 1852-22009. It supersedes DD ENV 1852-22001 which is withdrawn. This publication is not to be regarded as a British Standard. It is being issued in the Draft for Development series of publications and is of a provisional nature. It should be applied on this provisional basis, so that ination and experience of its practical application can be obtained. Comments arising from the use of this Draft for Development are requested so that UK experience can be reported to the international organization responsible for its conversion to an international standard. A review of this publication will be initiated not later than 3 years after its publication by the international organization so that a decision can be taken on its status. Notification of the start of the review period will be made in an announcement in the appropriate issue of Update Standards. According to the replies received by the end of the review period, the responsible BSI Committee will decide whether to support the conversion into an international Standard, to extend the life of the Technical Specification or to withdraw it. Comments should be sent to the Secretary of the responsible BSI Technical Committee at British Standards House, 389 Chiswick High Road, London W4 4AL. The UK participation in its preparation was entrusted to Technical Committee PRI/88, Plastics piping systems. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. 标准分享网 w w w .b z f x w .c o m 免费下载 w w w . b z f x w . c o m DD CEN/TS 1852-22009 TECHNICAL SPECIFICATION SPCIFICATION TECHNIQUE TECHNISCHE SPEZIFIKATION CEN/TS 1852-2 May 2009 ICS 23.040.01; 93.030Supersedes ENV 1852-22000 English Version Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene PP - Part 2 Guidance for the assessment of conity Systmes de canalisations en plastique pour les branchements et les collecteurs dassainissement sans pression enterrs - Polypropylne PP - Partie 2 Guide dvaluation de la conit Kunststoff-Rohrleitungssysteme fr erdverlegte drucklose Abwasserkanle und -leitungen - Polypropylen PP - Teil 2 Empfehlungen fr die Beurteilung der Konitt This Technical Specification CEN/TS was approved by CEN on 10 December 2007 for provisional application. The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to their comments, particularly on the question whether the CEN/TS can be converted into a European Standard. CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS available promptly at national level in an appropriate . It is permissible to keep conflicting national standards in force in parallel to the CEN/TS until the final decision about the possible conversion of the CEN/TS into an EN is reached. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre Avenue Marnix 17, B-1000 Brussels 2009 CENAll rights of exploitation in any and by any means reserved worldwide for CEN national Members. Ref. No. CEN/TS 1852-22009 E w w w . b z f x w . c o m DD CEN/TS 1852-22009 CEN/TS 1852-22009 E 2 Contents Page Foreword .............................................................................................................................................................. 3 Introduction ......................................................................................................................................................... 4 1Scope ............................................................................................................................................................ 5 1.1General ...................................................................................................................................................... 5 1.2Applicability .............................................................................................................................................. 5 2Normative references ................................................................................................................................. 5 3Definitions, symbols and abbreviations ................................................................................................... 5 3.1Definitions ................................................................................................................................................. 5 3.2Abbreviations ........................................................................................................................................... 7 4Requirements .............................................................................................................................................. 8 4.1General ...................................................................................................................................................... 8 4.2Testing and inspection ............................................................................................................................ 8 4.2.1Material specification ............................................................................................................................ 8 4.2.2Grouping ................................................................................................................................................. 8 4.2.3Type tests TT ........................................................................................................................................ 9 4.2.4Batch release tests BRT ................................................................................................................... 12 4.2.5Process verification tests PVT ......................................................................................................... 13 4.2.6Audit tests AT .................................................................................................................................... 14 4.2.7Indirect tests IT .................................................................................................................................. 15 4.2.8Inspection records and test records .................................................................................................. 16 Bibliography ...................................................................................................................................................... 17 标准分享网 w w w .b z f x w .c o m 免费下载 w w w . b z f x w . c o m DD CEN/TS 1852-22009 CEN/TS 1852-22009 E 3 Foreword This document CEN/TS 1852-22009 has been prepared by Technical Committee CEN/TC 155 “Plastics piping systems and ducting systems”, the secretariat of which is held by NEN. This document supersedes ENV 1852-22000. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. System Standards are based on the results of the work undertaken in ISO/TC 138 “Plastics pipes, fittings and valves for the transport of fluids“, which is a Technical Committee of the International Organization for Standardization ISO. They are supported by separate standards on test s to which references are made throughout the System Standard. The System Standards are consistent with general standards on functional requirements and on recommended practice for installation. EN 1852 consists of the following Parts, under the general title Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene PP  Part 1 Specifications for pipes, fittings and the system  Part 2 Guidance for the assessment of conity the present Technical Specification  Part 3 Guidance for installation Technical Specification According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to announce this Technical Specification Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. w w w . b z f x w . c o m DD CEN/TS 1852-22009 CEN/TS 1852-22009 E 4 Introduction This Technical Specification is intended to serve as a guide for the assessment of conity of products covered by EN 1852-1. It can be used integrally and/or be used for inclusion of conity assessment in the manufacturers quality plan as part of the quality system for attestation purposes. The use of this Technical Specification does not necessarily imply the involvement of a third party. It can also be used to support the elaboration of national third party certification procedures for products coning to EN 1852-1. It is the responsibility of the manufacturer to choose or not to choose for the involvement of a third party for certification purposes. 标准分享网 w w w .b z f x w .c o m 免费下载 w w w . b z f x w . c o m DD CEN/TS 1852-22009 CEN/TS 1852-22009 E 5 1 Scope 1.1 General This Technical Specification gives guidance for the assessment of conity to be included in the manufacturers quality plan as part of the quality system. This Technical Specification includes a requirements for materials, components, joints and assemblies given in EN 1852-1; b requirements for the manufacturers quality system; NOTE 1 It is recommended that the quality system cons to EN ISO 90012008 [1]. c definitions and procedures to be applied if third party certification is involved. NOTE 2 If third party certification is involved, it is recommended that the certification body is accredited to EN 450111998 [2] or EN ISO/IEC 170212006 [3], as applicable. 1.2 Applicability This Technical Specification is applicable to piping systems made of polypropylene PP intended to be used for a non-pressure underground drainage and sewerage outside the building structure application area code “U“, reflected in the marking of products by “U“, and b for non-pressure underground drainage and sewerage for both buried in the ground within the building structure application area code “D“ and outside the building structure application area code “U“, reflected in the marking of products by “UD“. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document including any amendments applies. EN 1852-12009, Plastics piping systems for non-pressure underground drainage and sewerage Polypropylene PP Part 1 Specifications for pipes, fittings and the system 3 Definitions, symbols and abbreviations For the purposes of this Technical Specification, the definitions, symbols and abbreviations given in EN 1852-12009, together with the following apply. 3.1 Definitions 3.1.1 certification body impartial body, governmental or non-governmental, possessing the necessary competence and responsibility to carry out certification of conity according to given rules of procedure and management w w w . b z f x w . c o m DD CEN/TS 1852-22009 CEN/TS 1852-22009 E 6 3.1.2 inspection body impartial organisation or company, approved by the certification body as possessing the necessary competence to verify and/to carry out initial type testing, audit testing and inspection of the manufacturers factory production control in accordance with the relevant European Standard 3.1.3 testing laboratory laboratory which measures, tests, calibrates or otherwise determines the characteristics of the perance of materials and products 3.1.4 quality system organisational structure, responsibilities, procedures, processes and resources for implementing quality management see EN ISO 90002005 [4] 3.1.5 quality plan document setting out the specific quality practices, resources and sequence of activities relevant to a particular product or range of products 3.1.6 modes of type testing 3.1.6.1 type testing TT testing pered to prove that the material, component, joint or assembly is capable of coning to the requirements given in the relevant standard 3.1.6.2 preliminary type testing PTT type testing carried out by or on behalf of the manufacturer 3.1.6.3 initial type testing ITT type testing carried out by or on behalf of the certification body for certification purposes 3.1.7 batch release test BRT test pered by the manufacturer on a batch of components, which has to be satisfactorily completed before the batch can be released 3.1.8 process verification test PVT test pered by the manufacturer on materials, components, joints or assemblies at specific intervals to confirm that the process continues to be capable of producing components coning to the requirements given in the relevant standard NOTE Such tests are not required to release batches of components and are carried out as a measure of process control. 3.1.9 audit test AT test pered by or on behalf of a certification body to confirm that the material, component, joint or assembly continues to con with the requirements given in the relevant standard and to provide ination to assess the effectiveness of the quality system 标准分享网 w w w .b z f x w .c o m 免费下载 w w w . b z f x w .