BS_EN_1504-8-2004_混凝土结构保护和维修用产品和系统．定义、要求、质量控制和合格评价．质量控制和合格评价.pdf

BRITISH STANDARD BS EN 1504-82004 Products and systems for the protection and repair of concrete structures Definitions, requirements, quality control and uation of conity Part 8 Quality control and uation of conity The European Standard EN 1504-82004 has the status of a British Standard ICS 91.080.40 BSI BS EN 1504-82004 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 November 2004 BSI 30 November 2004 ISBN 0 580 44921 1 National foreword This British Standard is the official English language version of EN 1504-82004. The UK participation in its preparation was entrusted by Technical Committee B/517, Concrete, to Subcommittee B/517/8, Protection and repair of concrete structures, which has the responsibility to A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests ined; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 10, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. DateComments BSI 标准分享网 w w w .b z f x w .c o m 免费下载 w w w . b z f x w . c o m EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1504-8 November 2004 ICS 91.080.40 English version Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and uation of conity - Part 8 Quality control and uation of conity Produits et systmes pour la protection et la rparation de structures en bton - Partie 8 Dfinitions, Prescriptions,matrise de la qualit et valuation de la conit - Partie 8 Contrle qualit et valuation de conit Produkte und Systeme fr den Schutz und die Instandsetzung von Betontragwerken - Definitionen, Anforderungen, Qualittsberwachung und Beurteilung der Konitt - Teil 8 Qualittsberwachung und Beurteilung der Konitt This European Standard was approved by CEN on 23 April 2004. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions English, French, German. A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre rue de Stassart, 36 B-1050 Brussels 2004 CENAll rights of exploitation in any and by any means reserved worldwide for CEN national Members. Ref. No. EN 1504-82004 E BSI w w w . b z f x w . c o m EN 1504-82004 E 2 Contents Page Foreword..............................................................................................................................................................3 1 Scope ......................................................................................................................................................4 2 Normative references............................................................................................................................4 3 Terms and definitions ...........................................................................................................................4 4 Sampling.................................................................................................................................................5 5 uation of conity.......................................................................................................................6 6 Marking and labelling............................................................................................................................7 7 Assessment, surveillance and certification of factory production control.....................................8 Annex A inative Provisions for assessment, surveillance and certification of factory production control.................................................................................................................................9 A.1 General....................................................................................................................................................9 A.2 Tasks for the inspection body..............................................................................................................9 A.2.1 Initial assessment of the production control......................................................................................9 A.2.2 Continuous surveillance of factory production control ....................................................................9 A.3 Task of the certification body.............................................................................................................10 A.3.1 Certification of factory production control .......................................................................................10 A.3.2 Measures in case of non-conity.................................................................................................10 BSI 标准分享网 w w w .b z f x w .c o m 免费下载 w w w . b z f x w . c o m EN 1504-82004 E 3 Foreword This document EN 1504-82004 has been prepared by Technical Committee CEN/TC 104 “Concrete and related products”, the secretariat of which is held by DIN. This Part of this European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by February 2005, and conflicting national standards shall be withdrawn at the latest by February 2005. It has been developed by sub-committee 8 “Products and systems for the protection and repair of concrete structures” Secretariat AFNOR. This Part of this European Standard specifies procedures for sampling, uation of conity, marking and labelling of products and systems for the protection and repair of concrete. This Part 8 of EN 1504 does not supersede any other document. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Construction Products Directive 89/106/EC. This Part of this European Standard is one of the Parts of this Standard on products and systems for the repair and protection of concrete structures, the other Parts are listed below EN 1504-1, Products and systems for the protection and repair of concrete structures Definitions, requirements, quality control and uation of conity Part Definitions prEN 1504-2, Products and systems for the protection and repair of concrete structures Definitions, requirements, quality control and uation of conity Part 2 Surface protection systems for concrete prEN 1504-3, Products and systems for the protection and repair of concrete structures Definitions, requirements, quality control and uation of conity Part 3 Structural and non-structural repair EN 1504-4, Products and systems for the protection and repair of concrete structures Definitions, requirements, quality control and uation of conity Part 4 Structural bonding prEN 1504-5, Products and systems for the protection and repair of concrete structures Definitions, requirements, quality control and uation of conity Part 5 Concrete injection prEN 1504-6, Products and systems for the protection and repair of concrete structures Definitions, requirements, quality control and uation of conity Part 6 Anchoring of reinforcing steel bar prEN 1504-7, Products and systems for the protection and repair of concrete structures Definitions Requirements Quality control and uation of conity Part 7 Reinforcement corrosion protection ENV 1504-9, Products and systems for the protection and repair of concrete structures Definitions, requirements, quality control and uation of conity Part 9 General principles for the use of products and systems EN 1504-10, Products and systems for the protection and repair of concrete structures Definitions Requirements Quality control and uation of conity Part 0 Site application of products and systems and quality control of the works According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. BSI w w w . b z f x w . c o m EN 1504-82004 E 4 1 Scope This Part of this European Standard specifies procedures for quality control and uation of conity, including marking and labelling of products and systems for the protection and repair of concrete according to EN 1504, Parts 2 to 7. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document including any amendments applies EN 1504-1, Products and systems for the protection and repair of concrete structures Definitions, requirements, quality control and uation of conity Part Definitions prEN 1504-2, Products and systems for the protection and repair of concrete structures Definitions, requirements, quality control and uation of conity Part 2 Surface protection systems for concrete prEN 1504-3, Products and systems for the protection and repair of concrete structures Definitions, requirements, quality control and uation of conity Part 3 Structural and non structural repair EN 1504-4, Products and systems for the protection and repair of concrete structures Definitions, requirements, quality control and uation of conity Part 4 Structural bonding prEN 1504-5, Products and systems for the protection and repair of concrete structures Definitions, requirements, quality control and uation of conity Part 5 Concrete injection prEN 1504-6, Products and systems for the protection and repair of concrete structures Definitions, requirements, quality control and uation of conity Part 6 Anchoring of reinforcing steel bar prEN 1504-7, Products and systems for the protection and repair of concrete structures Definitions, requirements, quality control and uation of conity Part 7 Reinforcement corrosion prevention EN ISO 9001, Quality management systems - Requirements ISO 900 2000 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 1504-1 and the following apply. 3.1 batch quantity of material made in a single operation, or in the case of continuous production for a defined quantity in tonnes which shall be demonstrated by the producer to have a uni composition and shall not exceed one day’s production. 3.2 identification test test carried out to verify a declared value of the composition or property of the product or system in terms of consistency of the production. NOTE This is to ensure that the product or system being tested corresponds to the product or system subjected to the initial type test, within the permitted tolerances. BSI 标准分享网 w w w .b z f x w .c o m 免费下载 w w w . b z f x w . c o m EN 1504-82004 E 5 3.3 perance test test carried out to verify a value for a required property of the product or system in terms of its specified perance during application and use. NOTE This is to ensure that the product or system cons to its specified perance characteristics. 3.4 declared value value declared and documented by the manufacturer for identification or perance requirements. 4 Sampling 4.1 General Sampling shall be carried out in such a way that the resulting sample is homogeneous and representative of the batch or product to be inspected. Samples shall be clearly labelled to uniquely identify the source, location and time of sampling. The sample size shall be sufficient for all the required testing in accordance with the relevant test standards. NOTE A part of the sample should be retained for future reference until the use by date. 4.2 Record All ination relevant to the sampling shall be recorded, including in particular a date of manufacture and sampling b unique identification of the product and of the samples c type of material and quantity of samples d name of the manufacturer e manufacturer’s batch identification number f quantity of batch or product represented by the sample g physical state h colour or appearance i names of the persons responsible for sampling. j of sampling 4.3 Frequency of sampling For frequency of sampling see frequency of testing in EN 1504 Parts 2 to 6. BSI w w w . b z f x w . c o m EN 1504-82004 E 6 5 uation of conity 5.1 General The compliance of the product or system with the requirement of this Part of this standard and the declared values including classe